OZMOTORSPORT

Hose & Fitting Builder

Build your hose setup with confidence. Select your hose type and size, then choose from compatible Aeroflow hose ends and fittings. The Hose Builder automatically filters compatible components and checks current stock before you add your build to the cart

BUILD A COMPATIBLE HOSE SETUP

Take the Guesswork Out of Hose & Fitting Selection

We've all done it - planned out the system to the nth degree, written the list down on a napkin, and run to the parts store to get everything (or ordered online). Only when it comes time for assembly, you find that you forgot a 90º, there is an extra 45º, and the two 120º fittings are in the wrong series! Again! We don't judge, really, so we made this OzMotorSport Hose & Fitting Builder for ourselves, as much as we made it for you. Use this to record the list of hoses and fittings you need to plumb up systems on your car, and rest easy knowing that you'll have everything you need.

1. Choose Your Hose

Start with the hose family and AN size required for your application, then select the colour and pack length you need.

2. Choose Each Hose End

Select the angle, hose-end style, connection size and finish for each end. Only compatible options are shown as you work through the builder.

3. Name & Save Your Hose

Give the hose a useful name such as “Oil Cooler Feed” or “Fuel Return”. Build as many hoses as you need before adding all the required components to your cart.

Please note: Hose and fittings are supplied as individual components. The builder assists with component selection and does not represent an assembled hose service.

Not sure which hose or fittings you need? Our Hose & Fitting Guide explains AN sizing, hose types, fitting styles, angles and connections before you start your build.
VIEW HOSE & FITTING GUIDE
STEP 1

Build Your Hose

1 Choose hose family & size
Select the style of connection you need to make, e.g. braided covered rubber hose, PTFE hose, etc...
Choose the size of the system in AN dash sizing.
Choose the hose first. Compatible hose-end families are filtered automatically.
2 Choose hose
Select from available finishes in the chosen series and size.
Enter length of the hose segment in centimetres. This will be calculated later into available hose sizes.
cm
Enter the finished hose length you need. Pack sizes are selected later when you calculate the complete build. Multiple hoses in the same series and size will be combined to minimise waste and prevent over-ordering an unnecessary amount of hoses.
3 Choose End 1
AN Flare Female is the default choice.
Choose fitting angle.
Select from variants, e.g. full flow.
Choose end size, different sizes here allow for stepped hoses.
Choose from available colours.
4 Choose End 2
Each end can use a different connection type. Stepped hose ends are supported: the hose size stays fixed while the connection size can differ.
5 Finalise hose
YOUR HOSE

Review selection

Choose a hose family to begin.
 
Use a name you'll recognise later in My Hoses and at checkout - this list of assignments can be printed or saved as a PDF for later use!
 
STEP 2

My Hoses

0 hoses
Hose builds are saved in this browser so they remain here if you leave or refresh the page - you can also print or save as PDF for later referral.
No hoses built yet.

Configure your first hose above and click Make Hose.

 

Choose an adapter for a compatible hose end already used in this build. Adapter options are filtered from the connection type and size selected on your saved hoses.

 
 
No adapters added. This section is optional - your hose build can go straight to cart without one.
OPTIONAL

Fire Sleeving

Compatible Heat Guard is shown automatically from the hose series and sizes in My Hoses. Add it only to the lines that need additional heat protection.

OPTIONAL

Tools & Accessories

Tools and assembly accessories are filtered to suit the hose families in this build. General AN assembly tools remain available for every build.

FINALISE

Optimise & Finalise Hose Lengths

Calculate the total hose required across your saved builds and select the smallest available pack combination for each hose type.
 
 
Important: Hose and fittings are supplied as individual components. The Hose Builder is designed to help select compatible parts and does not represent an assembled hose service.